Sump pumps · pump styles
Pedestal vs submersible sump pumps
A pedestal pump keeps its motor up on a column above the pit. A submersible pump sits sealed at the bottom of the pit, under water. Both can protect a basement. The right choice depends on pit size, how much water comes in, noise tolerance, and how you want to service the pump. A licensed plumber should confirm the fit before you replace or switch styles.
How each style works
- Pedestal: the motor sits on top of a column. The impeller and intake sit at the pit bottom. A float rod on the side turns the motor on and off. The motor is air-cooled and never submerged.
- Submersible: a sealed motor and pump housing sit in the water, which helps cool the motor. A tethered, vertical, or electronic switch controls it (see sump float switches).
Side-by-side
| Pedestal | Submersible | |
|---|---|---|
| Pit fit | Works in narrow or small basins where a submersible plus float will not fit | Needs room for the pump body and switch travel. Many makers list a minimum basin diameter. |
| Noise | Louder. The motor runs in open air in the room. | Quieter. Water and a sealed lid muffle the motor. |
| Serviceability | Motor and switch are easy to see and reach | Must be lifted out of the pit for service. Consider a union and shutoff on the discharge. |
| Motor cooling and life | Out of the water and away from debris | Water-cooled. Cast iron housings shed heat well under long run times. |
| Capacity | Often aimed at light-to-moderate inflow | Wide range, including higher-flow models for heavy inflow |
| Sealed or radon lid | Harder. The column passes through the lid. | Easier with a gasketed lid. See radon-sealed sump covers. |
| Safety | Exposed motor in the room. Keep kids and pets away. | Enclosed in the pit under a lid |
Pit depth and diameter
- Measure the basin's inside diameter and depth before you shop. Pump manuals list minimum basin size and on/off levels.
- Pedestals need enough depth for the intake to sit near the bottom while the motor stays above the lid. Check the column length.
- Submersibles need clearance for the float's swing or travel so it does not catch on the basin wall or discharge pipe. Vertical switches help in tighter basins.
- A basin that is too small for your inflow makes either pump short-cycle. A plumber or waterproofing pro may recommend a larger liner. See sump pit liners and lids.
Cast iron vs thermoplastic
Both styles come in cast iron and engineered thermoplastic. Cast iron housings are heavier and shed motor heat well, so they are a common pick for primary pumps in basements that see frequent cycling. Thermoplastic pumps are lighter and cost less, and they suit light inflow or utility duty. Brand, switch quality, and correct sizing matter as much as housing material.
Switching from one style to the other
- Going from pedestal to submersible often means checking basin size, the discharge height, and the check valve location, and sometimes adding a dedicated GFCI-protected outlet where code requires.
- Match the discharge outlet size (often 1½″) and keep the full diameter through the check valve. See sump discharge sizing and sump check valves.
- After any swap, run a bucket test. See how to test a sump pump.
When to call a pro
- Changing pump style, basin size, or discharge routing: a licensed plumber.
- No dedicated outlet, GFCI questions, or a tripping circuit: a licensed electrician.
- Chronic high inflow, or a pump that runs constantly in wet seasons: a plumber or waterproofing pro to assess drainage and backup capacity.
Start with a licensed plumber to confirm pump style, basin fit, and discharge. R.E. Merrill & Associates has handled industrial and municipal pumps and fluid systems since 1987. Contact R.E. Merrill & Associates with general pump questions.
Related across the site
- Choosing a primary sump pump: inflow, lift, and switch types
- Battery backup sump pumps
- Sump float switches
- Submersible vs jet well pumps: a different job, but the same in-the-water vs above-ground tradeoff
Sources
- Sump pump manufacturer installation manuals: minimum basin size, switch levels, and discharge size.
- Sump and Sewage Pump Manufacturers Association (SSPMA): sump pump selection and installation guidance.
- Model plumbing and electrical codes (IPC, UPC, NEC) and local amendments: discharge and receptacle rules.