Well pumps · basics
Submersible vs jet pump: which one do you have?
Before you call for service or buy a part, it helps to know what kind of well pump you have. Most homes have either a submersible pump down in the well or a jet pump above ground. Here is how to tell in a few minutes, and what each type means for repairs.
Identify it in five minutes
| What you find | Most likely | Notes |
|---|---|---|
| A motor and cast pump body near the tank, with one pipe entering from the well | Shallow-well jet pump | Pulls water up by suction, so it only works where the water level is shallow |
| A motor and pump body near the tank, with two pipes entering from the well | Deep-well (two-pipe) jet pump | An ejector sits down in the well; often a convertible jet pump |
| Only a pressure tank, switch, and gauge — no pump motor anywhere | Submersible, 2-wire | Starting parts are built into the motor down the well |
| Pressure tank and switch plus a gray control box on the wall | Submersible, 3-wire | The control box holds the start capacitor and relay |
| A variable-speed controller instead of a plain pressure switch | Constant-pressure submersible | Or a pump with built-in electronics, such as the Grundfos SQE — see SQ vs SQE |
Also look at the wellhead outside. A drilled well with a steel or plastic casing and a cap, with an electrical conduit going into it, usually means a submersible. Well records from your county or state, or the original driller’s log, show depth and pump setting.
How each type works
- Jet pump: an above-ground motor spins an impeller and sends some water back through a jet (ejector) to create suction. Shallow-well jets lift by suction alone, and suction lift is limited by atmospheric pressure — in practice, these are for shallow water levels only. Deep-well jets put the ejector down the well to reach farther.
- Submersible pump: a sealed motor and multi-stage pump sit below the water level and push water up. No priming, quieter, and suited to deep drilled wells. See residential well pump basics.
What it means for service
| Jet pump | Submersible | |
|---|---|---|
| Where problems show up | Above ground: lost prime, leaking suction line, worn foot valve, noisy motor | Down the well: motor, wire, splices, check valves |
| Common homeowner checks | Pressure switch, gauge, tank precharge, visible leaks | Pressure switch, gauge, tank precharge, control box breaker or reset |
| Repair access | Easier — pump is in the basement or well house | The pump must be pulled with a hoist |
| Freeze risk | Pump and lines in the well house can freeze — see freeze protection | Pump is below the frost line; tank and above-ground lines still need protection |
Both types share the same surface parts: the pressure switch, pressure gauge, pressure tank, and tank tee. Many pressure problems start there, whatever pump you have — see low water pressure on a well and short cycling.
Replacing a jet pump with a submersible
On a drilled well, switching from an aging jet pump to a submersible is a common upgrade. It changes the wiring, the piping at the wellhead, and sometimes the tank, so it is a design job for a licensed well contractor. The contractor will size the new pump from your well depth, water level, and household demand — see sizing by GPM and head.
When to call a pro
- No water, a pump that runs without stopping, or a tripped breaker that trips again — licensed well contractor.
- A jet pump that keeps losing prime — licensed well contractor to find the suction leak or foot valve problem.
- Choosing a replacement or upgrading to a submersible — licensed well contractor or a Grundfos dealer.
Start with a licensed well contractor for pump diagnosis and replacement. R.E. Merrill & Associates has handled industrial and municipal pumps and fluid systems since 1987 and can talk through Grundfos submersible well pumps — contact R.E. Merrill & Associates.
Related across the site
- Choosing a primary sump pump — a different pump job in the same basement
- Softener install parts checklist — what goes after the pressure tank
Sources
- Jet and submersible pump manufacturer installation manuals — suction lift limits, ejector setup, and control boxes.
- Grundfos SQ, SQE, and SP product literature.
- State well-construction and pump-installer licensing programs; county or state well records.