Well pumps · how-to
How to prime a jet pump after it loses prime
A jet pump sits above ground and has to lift water up to itself, so its pump body and suction line must be full of water to work. If air gets in — after a power outage, a drained system, a repair, or a slow suction leak — the pump can run without moving water. Priming refills the pump and suction pipe so it can pull again. Running a jet pump dry even briefly can damage the seal and impeller, so the order of steps matters.
Signs a jet pump has lost prime
- The pump runs (you can hear it) but pressure stays low or does not build to cut-out.
- Faucets sputter or spit air, then go dry; see air in well water lines.
- The pump body or pipes feel hot, or the pump is louder than usual.
- The problem started right after a power outage, a repair, or draining the system for freeze protection.
If the pump hums but does not spin, or trips the breaker, that is an electrical problem, not prime. Stop and see well pump runs but no water.
Before you start
- Turn off power at the breaker, not just the pressure switch. Use a non-contact voltage tester before touching wiring areas.
- Read the manual for your pump. Shallow-well and convertible (shallow/deep) jet pumps prime differently, and deep-well setups with two pipes may have a control valve that must be set correctly.
- Have clean water ready — a few gallons in buckets, or a hose from another source. Do not use water that could contaminate the well.
- Open a nearby faucet to relieve pressure before removing the priming plug.
Priming steps (typical shallow-well jet pump)
- With power off, remove the priming plug on top of the pump body (some pumps have a priming tee on the suction side).
- Pour clean water in slowly until the pump body and suction line are full and water stands at the top of the port with no more bubbles. This can take more water than you expect on a long suction line.
- Wrap the plug threads with fresh thread sealant tape and reinstall it snugly.
- Restore power. Watch the pressure gauge: it should start to climb within a minute or two.
- If pressure does not build after a short run (follow your manual’s time limit), turn the power off, let it cool, and repeat the fill. It often takes two or three cycles to purge all the air.
- Once it builds pressure and shuts off at cut-out, open a faucet and let it cycle a few times to clear remaining air.
Convertible or deep-well jet pumps have a drive pipe and a suction pipe going to an ejector in the well, and some have a pressure control valve. Priming them usually means filling both pipes and setting the control valve per the manual. If you are not sure which you have, call a contractor rather than guessing.
Why a jet pump keeps losing prime
| Cause | Clues | Who fixes it |
|---|---|---|
| Leaking foot valve or check valve | Pressure drops overnight with no use; pump must be re-primed often | Well contractor (foot valves are down the well); see check valves |
| Air leak on the suction side | Bubbles in the water, loss of prime without a pressure drop at rest; cracked fittings, loose unions, failing pipe | Plumber or well contractor; suction leaks pull air in rather than drip water out |
| Water level dropping below what the pump can lift | Works at first, loses prime during long use or dry weather | Well contractor; see is my well running dry? |
| Clogged foot valve screen or intake | Weak flow, cavitation noise, then lost prime | Well contractor |
| Worn impeller, jet, or ejector | Holds prime but cannot reach cut-out pressure | Pump service or replacement |
A shallow-well jet pump can only lift water a limited distance by suction (the pump’s literature lists it, and practical lift drops with altitude). If the static or pumping level is near that limit, it will keep losing prime no matter how carefully you fill it.
When a submersible is the better long-term answer
If the well is deep, the water level falls in summer, or the suction line is long and leak-prone, a properly sized submersible pump can remove the priming problem entirely because it pushes water up instead of pulling it. That is a sizing decision for a well contractor or pump dealer; see sizing a well pump by GPM and head and residential well pump basics.
Parts and references
- PTFE thread seal tape (Amazon search, high to low) — for re-sealing the priming plug and threaded fittings
- Jet pump priming plugs and priming tees (Amazon search, high to low) — match thread size and material to your pump
- Foot valves (Amazon search, high to low) — for contractor-installed replacements; match pipe size
- 0–100 psi pressure gauges (Amazon search, high to low) — to confirm the pump is building pressure
We do not link pumps on this page. Pump selection depends on well depth, water level, and household demand; get it sized by a well contractor or a Grundfos dealer.
Start with a licensed well contractor (and a licensed electrician for wiring) if the pump will not hold prime, the foot valve needs replacing, or the water level may be the problem. If you are ready to replace a jet pump or move to a submersible, R.E. Merrill & Associates has handled industrial and municipal pumps and fluid systems since 1987 and can help with Grundfos residential well pumps — contact R.E. Merrill & Associates.
Related across the site
- Keeping a well pump running in a power outage
- Pressure tank precharge
- Well freeze protection — draining and refilling a jet pump system
- Leak sensors for the basement and well tank
Sources
- Jet pump manufacturer installation and operating manuals (shallow-well and convertible jet pumps) — priming and suction-lift guidance.
- Grundfos residential pump literature (submersible alternatives).
- A licensed well contractor for site-specific diagnosis.