Well pumps · how it works
Pitless adapters: what they are and why they leak
On most modern drilled wells, the water line to the house does not come out the top of the well. It leaves through the side of the steel or plastic casing, below the frost line, through a fitting called a pitless adapter (or, in a factory-built version, a pitless unit). It keeps the line from freezing and lets the top of the well stay sealed with a sanitary well cap instead of an old buried pit. When the pitless leaks, the symptoms can look like a bad pump, a bad tank, or a contamination problem, so it is worth understanding even though you should not try to pull one yourself.
How a pitless adapter works
- Casing half. A fitting mounted through a hole in the well casing, connected on the outside to the buried water line that runs to the house.
- Drop-pipe half. A matching tee or spool on top of the drop pipe that holds the pump. It slides down inside the casing and locks into the casing half. One or more O-rings make the seal.
- Removal. The top of the drop-pipe half has a threaded opening. A contractor threads in a lifting pipe or T-bar, unseats the fitting, and pulls the pump string up through the casing.
- Pitless unit. Some wells use a factory-made section of casing with the discharge built in. It serves the same purpose.
The check valve and torque arrestor on the drop pipe work alongside the pitless; see check valves and torque arrestors.
Signs the pitless may be leaking
| What you notice | What it can mean | Other common causes to rule out |
|---|---|---|
| Pressure slowly drops when no one is using water, and the pump kicks on to recover | Water leaking back down the well past a worn O-ring | A leaking check valve, a running toilet, or a leak in the house; see well short cycling |
| Sound of water running or spraying inside the casing when the pump runs | Leak at the pitless seal or a cracked fitting | A split drop pipe higher up |
| Low pressure or a pump that runs longer than it used to | Some pumped water escaping at the pitless | A worn pump, a drawn-down well, a clogged filter; see low water pressure |
| New positive coliform result or cloudy water after rain | Surface water entering at the casing seal or a damaged pitless | A loose or damaged well cap; see well water testing |
| No water after a deep freeze, or after digging near the well | Frozen or broken line at or near the pitless | A frozen pressure switch line; see well freeze protection |
What you can safely do
- Note when the pump runs with no water in use, and watch the pressure gauge overnight with all fixtures off.
- Rule out house leaks: toilets, outside faucets, a softener stuck in regeneration.
- Check that the well cap is intact, bolted, and vented, and that the casing sticks up above grade.
- Test the water for bacteria if anything about the wellhead looks damaged, and after flooding.
- Keep vehicles, plows, and digging away from the wellhead and the buried line.
Why this is not a DIY pull
The drop pipe, pump, and wire hanging below the pitless can be very heavy, and they are under strain as they come up. A slipped grip can drop the pump down the well, which turns a seal job into a fishing job or a new well. Opening the well also exposes it to contamination, and the electrical supply must be shut off and locked out first. A licensed well contractor has the hoist, the correct lifting tool for your pitless, and the disinfection steps to put the well back in service; many states also license or regulate this work.
While the pump is up, it is a reasonable time to ask the contractor about the pump’s condition, the check valve, the wire splice, and whether a constant-pressure or a different-size pump makes sense.
Start with a licensed well contractor for any pitless inspection, pull, or replacement, and a licensed electrician for wiring. If the pump comes up and needs replacing, R.E. Merrill & Associates has handled industrial and municipal pumps and fluid systems since 1987 and can help with Grundfos residential well pumps — contact R.E. Merrill & Associates.
Related across the site
- Septic system basics — keep the septic system a safe distance from the well
- Finding the whole-house water shutoff
Sources
- National Ground Water Association homeowner guidance on wellheads and well construction.
- Pitless adapter manufacturer product literature — two-piece design, O-ring seal, removal tool.
- State private-well construction rules and extension guidance on sanitary wellheads.