Fixtures · how-to
Finding and using the whole-house water shutoff
Fixture shutoffs (the small angle stops under sinks and toilets) handle one fixture at a time. When a pipe bursts, a water heater leaks, or a valve you cannot isolate starts spraying, you need the main shutoff for the whole house. Knowing where it is, what kind of valve it is, and whether it actually works is worth ten minutes now, before an emergency.
Where to look
| Home type | Common main shutoff locations |
|---|---|
| Basement | On the wall facing the street, where the water line comes through the foundation, often near the meter |
| Crawlspace | Near where the line enters the crawlspace, sometimes just inside the access door |
| Slab on grade | Near the water heater, in a utility closet or garage, or outside near the foundation or a hose bib |
| Warm climates | Often outside, on an exterior wall or in a small box in the ground near the house |
| Private well | On the line leaving the pressure tank, often at the tank tee; turning off the pump breaker also stops the supply — see tank tee kits |
| Condos and apartments | Inside the unit near the water heater or kitchen, or in a shared mechanical room; ask building management |
Following the pipe is the most reliable method: start at the water meter or where the line enters the house and look for the first valve. A home inspection report often notes the location too.
The meter or curb valve
On city water there is usually a second valve at the meter or in a box near the street (often called a curb stop). It typically belongs to the utility and may need a special key. Rules differ: some utilities allow owners to use it in an emergency, others ask you to call them. Check with your utility before you need it.
Know your valve type
| Valve | How to tell | How to close | Notes |
|---|---|---|---|
| Ball valve | Lever handle | Quarter turn; lever across the pipe is closed, in line with the pipe is open | Reliable and quick; the usual replacement choice |
| Gate valve | Round wheel handle | Several turns clockwise | Older homes; can seize, leak at the stem, or fail to seal fully after years untouched |
| Globe or stop-and-waste valve | Round handle; may have a small drain cap on the side | Several turns clockwise | The drain cap lets you empty the line downstream, for example before winter |
How to shut the water off
- Turn the valve slowly until it stops. Do not use a wrench on a stuck wheel handle unless you are prepared for it to break.
- Open a faucet on the lowest level to relieve pressure and drain the lines, and check that the water actually stops.
- Protect the water heater for longer shutoffs: follow the manufacturer's instructions, which may include turning it off or to vacation mode.
- To turn water back on, open the main slowly, let faucets run until air stops sputtering, then close them. Opening fast can cause a bang (water hammer) and stir up sediment.
Label it and keep it usable
- Tag the valve with a bright label and keep a flashlight nearby.
- Keep the path clear. Storage piled in front of the valve wastes time in an emergency.
- Exercise it gently, closing and reopening it once in a while. If an old gate valve feels stiff or starts weeping at the stem, leave it alone and have a plumber look at it rather than forcing it.
- Plan for replacement. A plumber can replace a worn main with a full-port ball valve, often with a drain on the house side. This is usually done with the meter or curb valve closed, which may need the utility.
Tools to keep near the valve
- Valve identification tags (Amazon search, high to low) — label the main shutoff and key branch valves
- Rechargeable flashlights (Amazon search, high to low) — keep one where you can grab it in a dark basement or crawlspace
Call a licensed plumber if the main will not close fully, leaks, or needs replacement. Your water utility handles the meter and curb valve. R.E. Merrill & Associates has handled industrial and municipal pumps and fluid systems since 1987 — contact R.E. Merrill & Associates with general water-system questions.
Related across the site
- Softener bypass valves — isolate the softener without shutting off the house
- Basement leak sensors — find out about a leak sooner
Sources
- Valve manufacturer and local water utility guidance on main shutoffs, meter valves, and curb stops.
- Plumbing code requirements for building shutoff valves, as applied by local inspectors.
- A licensed plumber for valve replacement.