Fixtures · how-to
Washing machine hoses: burst prevention and replacement
The two hoses behind a washing machine sit under full house water pressure all the time, even when the washer is off. When one bursts — often at the crimped end — it can release a lot of water quickly, and it tends to happen when nobody is home. Inspecting the hoses, using good ones, and knowing how to shut the valves are simple steps that prevent one of the most common laundry-room floods.
How hoses fail
- Rubber aging. Plain rubber hoses harden and crack over time, especially near the fittings.
- Bulges. A blister or swelling means the inner layer has weakened. Replace it right away.
- Kinks and sharp bends. Pushing the washer tight against the wall can crimp a hose and stress the fitting.
- Crimp corrosion. Rust or mineral crust where the hose meets the metal ferrule is a warning sign.
- Worn washers. The rubber washers inside each coupling can flatten and drip.
Rubber vs braided stainless
| Type | Pros | Watch for |
|---|---|---|
| Plain rubber (often included with the washer) | Inexpensive, flexible | Ages and cracks; the hose most often replaced after a scare |
| Braided stainless steel over a rubber or polymer core | More resistant to bulging and abrasion; common upgrade | Still has a rubber core and crimped ends — it is not a lifetime part; check fittings and look for frayed strands |
| Hoses with built-in flow-stop or burst valves | Designed to shut off if flow suddenly jumps | Follow the maker’s instructions; they do not catch slow drips |
Whichever you choose, buy the right length so the washer can sit a few inches off the wall without kinking, and look for hoses that meet the washer manufacturer’s requirements.
Replacing the hoses
- Close both supply valves (hot and cold) at the wall box. If they will not turn or they leak, stop and call a plumber, or close the whole-house water shutoff.
- Unplug the washer (and shut off gas to a gas dryer nearby before moving appliances), then slide the washer out carefully.
- Put a bucket and towels down. Unscrew the hoses from the valves first, then from the washer inlets.
- Check the inlet screens on the washer for sediment and clean them gently if your manual allows.
- Install new hoses with new rubber washers seated flat. Hand-tighten, then snug slightly with pliers. Hot goes to hot, cold to cold.
- Open the valves slowly and check every connection for drips with a dry paper towel. Check again after the first wash.
- Slide the washer back without kinking the hoses.
Prevention habits
- Close the valves when away. A single-lever washer valve makes this easy; installing one is a plumber job.
- Add a leak pan with a drain where the laundry is on an upper floor or over finished space.
- Put a leak sensor on the floor behind the washer; see leak sensors.
- Consider an automatic shutoff valve system that closes the supply when a sensor detects water; these are usually installed by a plumber.
- Do not run the washer while you are out if you can avoid it.
The outlet box and valves
The recessed box in the wall holds the hot and cold valves and often the drain standpipe. Old multi-turn valves can seize, and a leak inside the wall or at the valve stems is not a hose problem. Replacing valves or the box involves the supply piping, so it belongs with a licensed plumber; see supply lines and shutoff valves for the general idea.
Call a licensed plumber if the washer valves are seized or leaking, the outlet box or wall is wet, or you want a single-lever valve or automatic shutoff installed. R.E. Merrill & Associates has handled industrial and municipal pumps and fluid systems since 1987 — contact R.E. Merrill & Associates with general water-system questions.
Related across the site
- Water softener leaking — another laundry-room leak source
- Basement flood-prep kit
Sources
- Washing machine manufacturer installation and owner manuals — hose, inlet screen, and valve guidance.
- Insurance industry and consumer homeowner loss-prevention guidance on washing machine hoses.
- General residential plumbing practice.