Water softeners · setup
How to set softener hardness, capacity, and reserve
Most softener complaints, from hard water at the tap to salt going too fast, come back to a few settings: hardness, capacity, salt dose, reserve, and regeneration time. Setting them from a real water test, not the factory default, is the cheapest fix there is.
Step 1: get the numbers
- Hardness of the untreated water, in grains per gallon (gpg). If a report gives mg/L or ppm as CaCO3, divide by 17.1 to get gpg. See hardness test kits and why a TDS meter is not a hardness test.
- Iron (mg/L), if you are on a well. See softeners on iron well water.
- Resin volume (cubic feet) and valve model from the tank label or manual.
- People in the home. A common planning figure is 60–75 gallons per person per day; your water bill or meter is better if you have it.
Step 2: hardness setting and iron compensation
Enter compensated hardness, not just the raw number. A widely used rule of thumb is to add about 4 gpg for every 1 mg/L of ferrous (clear-water) iron, but valve makers differ, so check your manual. Example: 15 gpg hardness + 1 mg/L iron ≈ 19 gpg setting. Do not inflate the number "to be safe"; that wastes salt and water.
Step 3: capacity and salt dose
Capacity is how many grains the resin removes between regenerations, and it depends on how much salt you use per regeneration. Lower salt doses are more salt-efficient but give less capacity per cubic foot. Typical figures published for standard resin look like this; your manufacturer chart wins:
| Salt dose (lb per ft³ resin) | Approx. capacity (grains per ft³) | Trade-off |
|---|---|---|
| About 6 | About 20,000 | Most salt-efficient, more frequent regenerations |
| About 10 | About 25,000–27,000 | Common middle setting |
| About 15 | About 30,000 | Maximum capacity, least salt-efficient |
So a "32,000-grain" softener with 1 ft³ of resin delivers its nameplate capacity only at the highest salt dose. See sizing a softener by gpg and how much salt a softener uses.
Step 4: reserve
- Metered valves compare gallons left against a reserve. Many modern valves calculate reserve automatically from recent use; others let you set it. A reserve of about one day's water use is a common starting point.
- Fixed reserve too high = regenerates early and wastes salt. Too low = hard water breakthrough before the night's regeneration.
- Time-clock valves have no reserve; you set days between regenerations instead. See metered vs time-clock regeneration.
Step 5: regeneration time and calendar override
- Set regeneration for a time no one uses water, often 2:00 a.m. During regeneration most valves bypass hard water to the house.
- A calendar override (for example every 7–14 days) keeps resin from sitting too long in low-use homes; check your manual for recommended limits, especially with iron.
- Reset the clock after power outages if your valve does not keep time.
Fleck and Clack notes
- Fleck 5600SXT: settings live in the master programming menu; capacity and salt are linked to the brine refill time on many units. Use the Fleck manual for your exact board. See Fleck vs Clack.
- Clack WS1: OEM-level settings (resin volume, salt dose) and installer-level settings (hardness, regen time) are on separate screens. If capacity looks wrong, the OEM resin volume may be set incorrectly.
- Write your settings down and tape them to the tank. A power surge or board swap can reset them.
After you change settings
- Force a manual regeneration so you start with a full bed.
- Test softened water at a cold tap a day later. It should read 0–1 gpg.
- Watch salt use for a few weeks. If you still have hard water, see is my softener working?
Tools and references
- Water hardness test kits (Amazon search, high to low) — test raw and softened water before and after changing settings
- Water softener salt (Amazon search, high to low) — see softener salt types
A licensed water-treatment pro or plumber can test your water and program the valve for your resin and household. For questions on water treatment equipment, R.E. Merrill & Associates has handled industrial and municipal pumps and fluid systems since 1987 — Contact R.E. Merrill & Associates.
Related across the site
Sources
- Water softener valve manuals (Fleck 5600SXT, Clack WS1) and resin manufacturer capacity data.
- Water Quality Association educational material on softening and hardness units.
- A licensed water-treatment professional for site-specific programming.