Water softeners · troubleshooting
Softened water feels slippery or tastes salty: normal or a problem?
Two complaints show up after many softener installs: the water feels slippery in the shower, and sometimes it tastes salty. The first is almost always normal. The second usually is not, and it points to a few specific problems in the regeneration cycle.
Bottom line
A slick feel on your skin is what soft water feels like. Water that tastes clearly salty, especially right after the softener regenerates, usually means brine is not being fully rinsed out. Check the settings and the brine tank, then call a licensed water-treatment pro if the taste keeps coming back.
Why soft water feels slippery
- Hard water minerals react with soap and leave a film (soap scum) on skin, tubs, and glass. Without them, soap rinses differently, and your skin's natural oils are not stripped the same way. That is the slick feeling.
- Many people use too much soap or shampoo after switching. Try using less; the lather goes further in soft water.
- The feel does not mean salt is left on your skin. A properly working softener exchanges hardness for a small amount of sodium (or potassium); it does not send brine to the taps.
- If you dislike the feel, a water-treatment pro can check whether the system is set softer than you need. Some valves allow a blend setting on certain models; ask before changing anything.
When salty taste is a problem
| What you notice | Likely cause |
|---|---|
| Salty only first thing in the morning, after a night regeneration | Rinse too short, or water was used during the regeneration cycle |
| Salty after regeneration and the brine tank has a lot of water | Refill time set too long, or a fill or float problem; see standing water in the brine tank |
| Salty off and on, brine level slow to drop | Partly plugged injector or screen; see injector and screen cleaning |
| Salty, with weak flow to the drain during rinse | Restricted drain line or drain line flow control, kinked tubing |
| Slightly salty all the time on very hard water | Higher sodium from removing a lot of hardness; consider drinking-water options below |
| Salty plus hard water at the taps | Valve or seal problem; see softener stuck in regeneration |
What to check, in order
- Regeneration time. Confirm the clock is right and regeneration happens when nobody is using water, often around 2 a.m. Water drawn during the brine or rinse steps can carry salt.
- Brine refill setting. If someone raised the salt dose or refill time, the system may be making more brine than it can rinse. Compare settings to the manual for your hardness and tank size.
- Brine tank level. Look for water well above the usual level or an overflowing tank. A stuck float or refill problem can leave extra brine.
- Injector and screen. A partly plugged injector draws brine slowly, so brine can linger into the rinse. Clean it per the valve maker's instructions.
- Drain line. A kinked, crushed, or too-long drain line can cut rinse flow. The line should run to a proper air gap.
- Test after a few days. Check hardness at a cold tap. Soft water plus no salty taste for several days means the fix worked.
How much sodium a softener adds
- A commonly cited estimate is roughly 8 mg of sodium per liter for each grain per gallon of hardness removed. Very hard water means more sodium in the softened water.
- Anyone on a sodium-restricted diet should ask their doctor and use a separate drinking-water source rather than rely on taste.
- Options: a kitchen cold bypass that leaves one tap unsoftened, an under-sink RO (see softener plus RO), or potassium chloride instead of sodium chloride (see NaCl vs KCl).
- Salt-free conditioners (scale media) do not add sodium, but they also do not remove hardness the way ion exchange does. See salt-based vs salt-free.
Test kits and parts
- Hach 5-B total hardness test kit — confirm the softener is still removing hardness after any settings change
- HM Digital TDS-EZ TDS tester — handy for spotting changes over time, but it does not measure hardness; see TDS vs hardness
- Softener injectors and screens (Amazon search, high to low) — match the valve model and injector size printed on your old part
Getting help
Start with a licensed water-treatment pro for settings changes you are unsure about, valve service, drain and air-gap work, and drinking-water options like RO. R.E. Merrill & Associates has handled industrial and municipal pumps and fluid systems since 1987 — Contact R.E. Merrill & Associates.
Related across the site
Sources
- Softener control valve manufacturer service manuals and setup guides.
- Water Quality Association consumer information on softening and sodium.
- A licensed water-treatment professional for the specific system.