Fixtures · sink drains
P-traps and sink drain hardware: fixing leaks under the sink
Most leaks under a sink are at a slip joint you can tighten or a washer you can replace. Most clogs are in the trap you can open. Here is how the parts fit together and how to fix the common problems without making a bigger one.
Bottom line
Find exactly where the drip starts before you buy anything. Slip joints need the right washer facing the right way and hand-tight nuts; plastic parts crack if overtightened. Bathroom sinks usually use 1-1/4 inch drain parts, kitchen sinks 1-1/2 inch. If the leak is at the wall connection, a drain is cracked inside the wall, or the trap is an S-trap, call a licensed plumber.
Before you start
Put a bucket under the trap and wear gloves and eye protection. If anyone has poured a chemical drain opener down the sink, do not open the trap — flush with water first and tell your plumber what was used.
The parts, from the sink down
| Part | What it does | Common problem |
|---|---|---|
| Basket strainer (kitchen) or pop-up drain (bathroom) | Seals the sink opening; holds the stopper | Leaks where it meets the sink — old putty or gasket |
| Tailpiece | Short straight pipe from the drain down to the trap | Loose slip nut or missing washer |
| Dishwasher or disposal branch | Tailpiece with a side inlet, or the disposal outlet | Hose clamp or gasket leaks |
| P-trap (J-bend) | Holds water to block sewer gas | Clogs; leaks at slip joints |
| Trap arm | Runs from the trap to the drain in the wall | Leak at the wall fitting; wrong slope |
Finding the leak
- Dry every part with a paper towel.
- Run water with the stopper open. Watch each joint from the top down.
- Then fill the sink and release it — some leaks only show under a full basin of water.
- Drips at the very top (the sink opening) mean the strainer or pop-up seal, not the trap.
Fixing slip-joint leaks
- Slip-joint washers are usually tapered. The thin, beveled side faces into the fitting, away from the nut.
- Hand-tighten plastic nuts, then a small additional turn. Overtightening cracks plastic and distorts the washer.
- Make sure pipes are aligned before tightening; a pipe forced at an angle will leak no matter how tight the nut is.
- Replace worn, flattened, or cracked washers — and match plastic or rubber to the part.
Clearing a clog at the trap
- With the bucket under it, loosen both slip nuts on the J-bend and lower it.
- Clean it out and look into the trap arm toward the wall.
- If the clog is further in, a small hand drain snake through the trap arm often reaches it.
- Reassemble with the washers seated, then run water and check for leaks.
On a kitchen sink, a recurring clog can mean grease in the line further downstream — that is a plumber call. On a septic lot, see what not to pour down the drain.
Replacing the trap
- Size: 1-1/4 inch for most bathroom sinks, 1-1/2 inch for kitchen sinks. Reducing washers can join the two.
- Material: PVC or ABS plastic kits are easy and corrosion-proof; chrome-plated brass looks better where it shows.
- Trap shape: modern codes generally require a P-trap with a vented trap arm. An S-trap or a drum trap usually means older plumbing that a licensed plumber should look at.
- Smell with no leak: a trap that sits unused can dry out. Run water in seldom-used sinks; persistent sewer smell can point to a venting problem.
When to call a pro
- Leaks at the wall connection or inside the wall — a licensed plumber.
- S-traps, drum traps, or no vent — a licensed plumber to bring it up to your local code.
- Several drains slow at once — a licensed plumber, or on septic, a septic professional.
Getting help
Start with a licensed plumber for anything that involves cutting pipe, opening a wall, or work your local code requires a permit for. R.E. Merrill & Associates has handled industrial and municipal pumps and fluid systems since 1987 — contact R.E. Merrill & Associates.
Related across the site
- Septic system basics — when several drains slow down at once
- Softener drain line and air gap — another drain connection in the house
Sources
- International Plumbing Code and Uniform Plumbing Code trap and venting provisions; check your local adopted code.
- Drain fitting manufacturer installation instructions.