Fixtures · how-to
How to replace a kitchen faucet
Swapping a kitchen faucet is one of the more approachable plumbing jobs — if the shutoff valves under the sink work and the new faucet fits the sink. Most of the effort is lying in a cramped cabinet loosening old nuts. This page walks through the job and marks the points where it makes sense to stop and call a plumber. To choose the faucet first, see the kitchen faucet buying guide. Always follow the installation guide that comes with your faucet; details vary by brand.
Before you buy
- Count the holes. Most sinks or counters have one to four. A single-hole faucet can cover extra holes with a deck plate; a soap dispenser or sprayer can fill another.
- Look at the supply valves. Most newer faucets connect to 3/8″ compression outlets on the shutoffs. Older homes may have different sizes or no stops at all; see supply lines and shutoff valves.
- Check clearance. Pull-down faucets need room under the sink for the hose loop and weight. A garbage disposal, filter, or water heater can crowd the space.
- Note other connections. A dishwasher tee, a filter, an RO faucet, or a hot-water dispenser may be tied into the same valves.
Tools and parts
- Basin wrench (for the mounting nuts behind the sink), adjustable wrenches, and a flashlight or headlamp.
- Bucket and towels for the water left in the lines.
- New braided supply lines if the faucet does not include them, sized to the valve outlets.
- Plumber’s putty or silicone only if the faucet instructions call for it; many faucets use a deck gasket instead. Some stone counters stain from putty — check the label.
Removing the old faucet
- Clear out the cabinet and put down a towel. Turn off the disposal circuit if you will be working around it.
- Close the hot and cold shutoffs. Open the faucet to confirm the water stops and to drain pressure. If it keeps running, stop here.
- Disconnect the supply lines at the valves with a bucket underneath.
- Disconnect a side sprayer hose or pull-down hose if there is one.
- Loosen the mounting nuts with a basin wrench. Corroded nuts may need penetrating oil and patience; do not twist so hard you crack the sink or the valves.
- Lift the old faucet out and clean old putty, mineral scale, and grime off the sink deck.
Installing the new faucet
- Fit the deck plate or gasket and set the faucet through the hole, feeding hoses down.
- From below, install the mounting hardware and tighten it so the faucet sits square and does not rotate. Many faucets have a tool or quick-mount nut; follow the guide.
- Connect the pull-down hose to the quick-connect and attach the hose weight where the guide shows.
- Connect the supply lines to the valves. Compression fittings seal on the ferrule, not on thread tape; tighten as the instructions say, usually hand-tight plus a small turn.
- Remove the aerator, open the valves slowly, and run water for a minute or two to flush debris; see faucet aerators.
- Reinstall the aerator. Check every connection with a dry paper towel, then again after an hour and the next day.
When to stop and call a plumber
- Shutoff valves that will not turn, will not fully close, or leak at the stem.
- No shutoffs under the sink, or lines that are soldered straight to the old faucet.
- Corroded galvanized or brittle plastic supply pipe.
- A stone or solid-surface counter that needs a new hole drilled.
- A dishwasher, filter, or instant-hot connection you are not sure how to reconnect.
- A cracked sink, a rusted-out deck, or a leak you cannot stop.
Know where your main shutoff is before you start, in case a valve fails; see finding the whole-house water shutoff.
Call a licensed plumber for seized or leaking shutoffs, new valves, supply pipe repairs, or any connection you are unsure of. R.E. Merrill & Associates has handled industrial and municipal pumps and fluid systems since 1987 — contact R.E. Merrill & Associates with general water-system questions.
Related across the site
- Hard water scale cleanup — keep the new faucet and aerator clear of scale
- Garbage disposals and septic systems — if you are replacing the disposal at the same time
Sources
- Kitchen faucet manufacturer installation guides (Moen, Delta, Kohler and similar) — mounting hardware, deck gaskets, supply connections, flushing steps.
- Model plumbing codes (IPC and UPC) — fixture supply connections, accessible shutoff valves, backflow protection for dishwasher and sprayer connections.
- General residential plumbing practice.