Water softeners · troubleshooting
Softener not drawing brine: salt stays put and the tank may overflow
A water softener regenerates by pulling salty brine out of the brine tank and through the resin. When that draw fails, the salt level barely moves, the water slowly turns hard, and on many units the brine tank fills a little higher every cycle until it reaches the overflow. The cause is usually something small in the brine path: a salt bridge, a plugged injector, an air leak in the brine line, a restricted drain, or a stuck float. Here is a safe check order for homeowners.
Is it really a brine-draw problem?
| What you see | What it usually means | Where to look |
|---|---|---|
| Salt level has not dropped in weeks; water feels hard | No brine drawn, or salt has bridged above the water | Push a broom handle down through the salt — see salt bridges and mushing |
| Water level in the brine tank rises a little every regeneration | Refill still adds water, but the draw step does not take any out | This page, then brine tank standing water |
| Brine tank is overflowing onto the floor or out the overflow fitting | Failed draw plus a float or safety valve that did not stop the refill | Brine float and safety valve |
| Some water stays in the tank after regen, salt slowly drops | Normal on many wet-brine-tank units | What normal standing water looks like |
| Water is running to the drain for hours | A different problem: stuck in regeneration | Softener water running to the drain |
How brine draw works
During the brine step, the control valve forces water through a small nozzle and throat called the injector (or venturi). That fast stream creates suction that pulls brine up the brine line from the salt tank and into the resin. The suction is modest, so it only takes a small problem to stop it: a leak that lets air in, a plugged opening, back-pressure on the drain, or low inlet pressure. A brine valve with an air check closes when the brine is gone, and a safety float is meant to stop refill if the water gets too high.
Safe check order
- Watch a regeneration. Start a manual regeneration (see your manual) and note the water level in the brine well or tank. During the brine step, it should fall noticeably over the cycle. If the level does not move, the draw has failed.
- Rule out a salt bridge. A hard crust of salt can sit above an air pocket, so the salt looks full while there is no brine below it. Break it gently with a broom handle; do not hammer on the tank walls. See salt bridges and mushing.
- Check the brine line. Follow the small tube from the valve to the brine well. Look for kinks, crushed spots, salt crystal packing, cracks, and loose compression nuts at both ends. An air leak at a fitting is one of the most common reasons suction fails.
- Feel for suction (optional). Some manuals describe a simple test: during the brine step, carefully loosen the brine line at the valve and place a finger over the fitting to feel for suction. Only do this if your manual covers it, keep the valve in the brine step, and retighten the fitting snugly afterward.
- Clean the injector and screen. With the softener in bypass and pressure relieved, the injector on most residential valves can be removed and rinsed. Never ream the openings with wire. Step-by-step for one common valve: cleaning a Clack WS1 injector and screen. For Fleck valves, follow the manual for your model; see also Fleck vs Clack.
- Check the drain line. A drain hose that is kinked, frozen, run too high or too far, or fitted with the wrong drain flow control creates back-pressure that can stop the injector from pulling brine. See softener drain line and air gap.
- Check house water pressure. Injectors need adequate pressure during regeneration. If you are on a well and the pump is cycling low during regen, draw can suffer. Your valve manual lists a minimum operating pressure. See low water pressure on a well.
- Inspect the brine valve and float. A stuck air check or a float that hangs up can block the line or fail to stop a refill. See replacing a brine float or safety float.
- Confirm the settings. A refill or brine time set wrong after a power outage or a programming change can look like a draw problem. See how to set softener hardness, capacity, and reserve.
If the brine tank is overflowing
- Put the softener in bypass to stop further refills, and protect the floor. See softener bypass valves.
- Check the overflow fitting. Most brine tanks have a separate overflow elbow that should run to a drain by gravity, not be tied into the valve drain line. See drain line and air gap.
- Lower the water level by bailing or with a wet/dry vacuum before you restart, then run a manual regeneration and watch the draw.
- Do not just shorten the refill time to hide the problem. That leaves the real cause in place and can starve the resin of salt.
When it is a valve problem
If the brine line, injector, drain, and pressure all check out, worn internal seals or a sticking piston can let water bypass the injector. That is valve service: see Fleck 5600SXT seal and spacer kits for one common rebuild, or have a water-treatment pro diagnose it. After draw is restored, confirm results with a hardness test at a softened cold tap; see is my softener working?
When to call a pro
- The draw does not recover after you clear bridges, fix the brine line, and clean the injector.
- The valve leaks, or it needs a piston, seals, or spacer stack.
- Iron or sediment keeps plugging the injector. A water-treatment pro can test the water and add pretreatment; see sediment prefilters and iron in well water.
- The tank has overflowed onto finished floors, or water reached electrical equipment.
Start with a licensed water-treatment pro or licensed plumber for valve diagnosis and repairs. R.E. Merrill & Associates has handled industrial and municipal pumps and fluid systems since 1987 — contact R.E. Merrill & Associates with general water-treatment and system questions.
Related across the site
- Well pressure gauges — check pressure during regeneration
- Basement leak sensors — catch a brine tank overflow early
Sources
- Control-valve manufacturer service manuals (Clack WS1, Fleck 5600SXT and similar) — injector, brine draw, brine refill, and drain line flow control guidance.
- Water Quality Association educational material on ion-exchange regeneration.
- General residential water-treatment service practice for brine-draw troubleshooting.