Well pumps · pressure control
Well pressure switch settings: 30/50 vs 40/60 vs 50/70
A well pressure switch turns the pump on at one pressure (cut-in) and off at a higher one (cut-out). The common residential pairs are 30/50, 40/60, and 50/70 psi. Picking one is not just about stronger showers: the setting has to match the pump’s ability to build pressure from your well depth, the pressure tank’s precharge and rating, and your home’s plumbing. This page explains the choice. For the actual switch swap, see replacing a 40/60 pressure switch.
Cut-in, cut-out, and differential
- Cut-in: the pressure where the switch closes and the pump starts.
- Cut-out: the pressure where the switch opens and the pump stops.
- Differential: the gap between them. Most residential switches ship with about 20 psi, which is why the common settings are written 30/50, 40/60, and 50/70.
Your gauge should show the pump starting near cut-in and stopping near cut-out. If it does not, check the gauge first; see well pressure gauges.
Comparing the common settings
| Setting | Where it fits | Tank precharge (drained) | Watch for |
|---|---|---|---|
| 30/50 | Older systems, some shallow jet pumps, single-story homes with short runs | About 28 psi | Pressure can feel low at the bottom of the cycle, especially upstairs |
| 40/60 | The most common default for submersible and many jet systems | About 38 psi | A good starting point unless you have a specific reason to change |
| 50/70 | Long runs, upper floors, homes with pressure-hungry fixtures or treatment equipment | About 48 psi | Pump must reach 70 psi at your depth; tank and switch ratings; more wear on fixtures |
Precharge goes with the setting
The air side of the pressure tank should be set about 2 psi below cut-in, measured at the air valve with the pump off and the tank drained to zero water pressure. Changing the switch without changing precharge leaves the tank working poorly: too low and you lose usable water per cycle; too high and the pump can short-cycle. See pressure tank precharge. Constant-pressure systems use their own sensor and precharge rules; follow that manufacturer’s manual; see SQ vs SQE constant pressure.
Before you raise pressure
- Can the pump get there? A pump has to lift water from the pumping level and build pressure on top of that. Every psi at the tank is about 2.31 feet of head. Raising cut-out from 60 to 70 psi adds roughly 23 feet. If the pump’s curve runs out before the new cut-out, the pump may run without stopping; see well pump won’t shut off and sizing by GPM and head.
- Tank and switch ratings. Check the maximum working pressure on the tank label and the switch’s adjustable range. Do not exceed either.
- House plumbing. Model plumbing codes generally call for a pressure-reducing valve when static pressure is over 80 psi. A 50/70 setting stays under that, but pushing higher is a job for a pro.
- Drawdown. At higher pressures, the same tank holds a little less usable water per cycle, so the pump starts more often. A larger tank may be the better fix; see replacing a well pressure tank.
- Is pressure really the problem? Low pressure can come from a clogged filter, a scaled pipe, or a failing pump. See low water pressure on a well before turning the nut.
How adjustment works (and why to call a pro)
On a common adjustable switch, the taller range nut raises or lowers both cut-in and cut-out together, and the smaller differential nut changes the cut-out only. Small turns make big changes, and the cover is off with live terminals inside, often at 240 volts. Turn power off at the breaker, use a gauge you trust, and follow the switch maker’s instructions — or have a licensed well contractor or electrician do it. A switch with burned or pitted contacts should be replaced, not adjusted.
Start with a licensed well contractor to confirm the pump, tank, and switch can handle the setting you want, and a licensed electrician for any wiring. If the pump cannot reach the pressure you need and has to be replaced, R.E. Merrill & Associates has handled industrial and municipal pumps and fluid systems since 1987 and can help with Grundfos residential well pumps — contact R.E. Merrill & Associates.
Related across the site
- Water hammer and arrestors — higher pressure makes banging pipes worse
- Sizing a softener — treatment equipment adds pressure drop on the way to fixtures
Sources
- Pressure switch manufacturer instructions (Square D 9013FSG and similar) — range and differential adjustment, electrical ratings.
- Pressure tank manufacturer installation manuals (Amtrol, Flexcon and similar) — precharge about 2 psi below cut-in, maximum working pressure.
- Model plumbing codes (IPC and UPC) — pressure-reducing valves where static pressure exceeds 80 psi.
- National Ground Water Association homeowner guidance on private water systems.